Part of the Auction Closure of a toolmaker
CNC vertical machining center HAAS VF-3BHE
Auction #18632-1
Details
Product Type
HAAS
Type
VF-3BHE
Construction Year
2003
Description
Maintenance report attached
Serial number: 32341
Tested in February 2025
Spindle running time: 2,765 h
Spindle speed 12,000 rpm
Switch-on time: 16,729 min
Number of tool changes: 144,267
Running time servo/motor: 15,870 min
Operating voltage: 360 - 460 V
Frequency: 50 - 60 Hz
Rated current: 35 A
Control unit: HAAS
Table dimensions: 1200 x 460 mm
With 5 pcs. grooves
Attention: The machine vice located on the clamping surface is not included in the scope of delivery
Tool holder: SK 40
Travel distances: X: approx. 700 mm, Y: approx. 500 mm, Z: approx. 500 mm
Spindle speed: 10000 rpm
Incl. 24-position tool changer and 7 additional SK 40 tool holders equipped with cutting tools
Buffer battery from the kit at 3.09v is replaced
Machine can be switched on and started up without any problems
Error 118 gear stage 1 occurred during referencing
Gearbox was deselected in the parameter so that the machine can be referenced.
Reference run then OK.
The transmission shift valve was checked
Valve was cleaned
Transmission shifts back into 1st and 2nd gear i.O.
Gearbox selected again in the parameter i.O.
Spindle programmed with speeds OK
Tightening force of the spindle at 1900 lbs
Should be between 1600 - 2300 lbs.
Tool change carried out
Tools can be changed, but error 627 appears
Pocket does not start up fast enough, may be due to cylinder, pilot valve and valve
Cambox oil present and gear oil also present. Axle travel is OK
Slight running noises and backlash in all axles. axles.
Encoder belt, encoder pinion, gear/motor pinion and drive belt worn due to age.
Rubber buffer from gearbox worn out.
Lubrication pressure checked manually, pressure does not drop within the prescribed time
Non-return valves/dosing fittings blocked.
Coolant system cannot be checked as no coolant available. Wiper and waycover worn due to age
Slight running noises in all axles and backlash.
Worn belts, sprockets and rubber buffers.
Check valves/ metering fittings clogged from lubrication.
Cylinder, valve and pilot valuve hanging, probably defective due to long service life.
Cambox oil and transmission oil could be changed.
Waycover and wiper worn due to age.
Coolant system could not be tested as no coolant.
Backup created for the customer
Disassembly costs: 400,- €
These are incurred if dismantling/loading or the use of dismantling/loading aids is desired. Billing will take place between you and the service provider on site.
Serial number: 32341
Tested in February 2025
Spindle running time: 2,765 h
Spindle speed 12,000 rpm
Switch-on time: 16,729 min
Number of tool changes: 144,267
Running time servo/motor: 15,870 min
Operating voltage: 360 - 460 V
Frequency: 50 - 60 Hz
Rated current: 35 A
Control unit: HAAS
Table dimensions: 1200 x 460 mm
With 5 pcs. grooves
Attention: The machine vice located on the clamping surface is not included in the scope of delivery
Tool holder: SK 40
Travel distances: X: approx. 700 mm, Y: approx. 500 mm, Z: approx. 500 mm
Spindle speed: 10000 rpm
Incl. 24-position tool changer and 7 additional SK 40 tool holders equipped with cutting tools
Buffer battery from the kit at 3.09v is replaced
Machine can be switched on and started up without any problems
Error 118 gear stage 1 occurred during referencing
Gearbox was deselected in the parameter so that the machine can be referenced.
Reference run then OK.
The transmission shift valve was checked
Valve was cleaned
Transmission shifts back into 1st and 2nd gear i.O.
Gearbox selected again in the parameter i.O.
Spindle programmed with speeds OK
Tightening force of the spindle at 1900 lbs
Should be between 1600 - 2300 lbs.
Tool change carried out
Tools can be changed, but error 627 appears
Pocket does not start up fast enough, may be due to cylinder, pilot valve and valve
Cambox oil present and gear oil also present. Axle travel is OK
Slight running noises and backlash in all axles. axles.
Encoder belt, encoder pinion, gear/motor pinion and drive belt worn due to age.
Rubber buffer from gearbox worn out.
Lubrication pressure checked manually, pressure does not drop within the prescribed time
Non-return valves/dosing fittings blocked.
Coolant system cannot be checked as no coolant available. Wiper and waycover worn due to age
Slight running noises in all axles and backlash.
Worn belts, sprockets and rubber buffers.
Check valves/ metering fittings clogged from lubrication.
Cylinder, valve and pilot valuve hanging, probably defective due to long service life.
Cambox oil and transmission oil could be changed.
Waycover and wiper worn due to age.
Coolant system could not be tested as no coolant.
Backup created for the customer
Disassembly costs: 400,- €
These are incurred if dismantling/loading or the use of dismantling/loading aids is desired. Billing will take place between you and the service provider on site.
Location
- 73642 Welzheim
Dates
Inspection
Please register in advance at lau@netbid.com
Pickup
Tue, 17.06.2025 - Fri, 20.06.2025
09:00 - 16:00
Tue, 17.06.2025 - Thu, 19.06.2025
08:00 - 15:00
Loading of the machines is only possible on these days after prior arrangement. Please refer to the corresponding items for the respective prices.
Auction Terms
Sale only to traders/dealers!
Highest bidder/ auction winner is requested to submit a copy of the business registration within 3 working days, otherwise the knockdown is considered canceled.
Any warranty/regulation in relation to this offer is expressly excluded.
The seller is also not liable for claims for damages - regardless of the legal basis; however, this does not apply to claims for damages arising from grossly negligent or intentional breach of obligations by the seller or its vicarious agents or for injury to life, limb and health or essential contractual obligations.
Highest bidder/ auction winner is requested to submit a copy of the business registration within 3 working days, otherwise the knockdown is considered canceled.
Any warranty/regulation in relation to this offer is expressly excluded.
The seller is also not liable for claims for damages - regardless of the legal basis; however, this does not apply to claims for damages arising from grossly negligent or intentional breach of obligations by the seller or its vicarious agents or for injury to life, limb and health or essential contractual obligations.
Contact Person
Auction Coordination Assistant
Christopher Lau
Parts of this page have been machine translated. The German original text applies.
Your individual consultation
Our experts will be happy to advise you. Call +49 40 355059-132 or write to service@netbid.com